WiFi of X6100 FW V1.1.5

I made a mistake. I wrote earlier that if you use WiFi of X6100 FW V1.1.5, you will not be able to restart, but it worked even with WiFi settings (PI fixed).
However, if I set Bluetooth (mouse + keyboard in my case) ... I can't restart.
You can restart with a WiFi connection.




X6100 power supply connect

How is this diagram in the manual supposed to confirm which is positive and which is negative?

The black wire appears to be the shielding and the white appears to be center pin. This, I'm assuming the white is positive and black is negative?



Black (-) White (+)

XIEGU X6100 Heat Testing - 20 minutes of FT8 at 5w produces too much heat

XIEGU X6100 Heat Testing - 20 minutes of FT8 at 5w produces too much heat 

I tried to warm up the radio today and measure the temperature by transmitting CQ on FT8. Unfortunately after about 20min the radio crashed with TX on and this happened twice.
Power 5W, external 12[V] power supply. The temperature reached 45 degrees.



XIEGU X6100 Running Hot

XIEGU X6100 Running Hot 
Are these radios designed to run hot or is it a flaw in the design?

XIEGU X6100 battery consumption in rx mode

XIEGU X6100 battery consumption in rx mode 
XIEGU X6100 running time on built in battery in rx mode

Hi i am doing my 4 charge/discharges , and on my last one now, The radio has been left to discharge just in rx mode on low volume,
and after a full charge the radio shuts down only after 3.5hrs, This does not seem correct as the manual says the radio only takes 330ma max in rx mode,
how long are users getting with there radio in rx mode on the internal battery,

XIEGU X6100 Battery Management System (BMS)

I found this info on the Radioddity Website discussing battery charging.

This X6100 charging method is what I had found. Charge with rig OFF, charge with LED flashing until off, then charge for about an additional hour.

When turn on rig just after LED stops flashing the displayed battery voltage was around 7.9V. If let charge for the additional hour then when turn on rig the battery voltage displayed was 8.2V.

During normal charging with rig OFF I found using ext supply the current draw was around 750ma. After LED off and additional charge the current dropped to less than 250ma.

This agrees with the explanation given.

X6100 will not turn on unless the power supply

In need of help my 6100 will not turn on unless the power supply is plugged in as soon as i unplug it it shuts off.


Understanding the X6100's heating due to the external power supply

I wanted to further understand the X6100's heating due to the external power supply's current and thus power (in watts) as the power supply's voltage is changed from 13.8 to 9 volts DC. The mode was CW and an external dummy load was used. See below for the data that I collected.

Some observations:

1.     In receiving only, the power to the X6100 stays constant at about 6 watts. My X6100 will get very warm after being on for 30 or more minutes. Note the X6100 manual specifies that the maximum receiving current would be a max of 330 ma. So much for Xiegu's specifications!


Solution: X6100 overheating

For those worried about overheating, please consider a couple of heat sinks. I ran my X6100 yesterday for over an hour on FT8/CW on 9 watts in the field with minimal heating issues. Made 20 POTA contacts.




XIEGU X6100 setup

Starting to prepare my kit... :)
These antennas will work hand held style, 40m to 6m bands are covered




Must not forget the high performance end fed.

XIEGU X6100 Reviews

XIEGU X6100 Reviews

This in not a KX2 or KX3 or a IC-705 and it does not cost $1200 either.

For me its better than a FT-818 and not better than IC-705.

It is a cheap experimental radio and fun to play with. To hack and mod freely. To tinker and maybe to break it while doing it... Did you ever imagined it would be possible to modify the UI accordingly to your taste in a HF rig? Now you can.

It should not be your first radio, it would be better if you spend more, or buy one of the big 3 used.

I rather have the X6100 in one pocket and an efhw in the other and have QSOs in 2 minutes than to spend extra 140USD in a cage and extra 120 in a pelican case and extra 300 in an external ATU [like the IC-705] and be worried about not to scratch any part of its plastic case.

X6100 Intermediate frequency leakage

Intermediate frequency leakage

I connected X6100 and TRX Amber through a divider to one antenna. And on Amber I saw the tuning frequency of the X6100. 

This is despite the fact that the divider provides an isolation between channels of -26 dB! - https://youtu.be/dulDlY00EmI

Was running some test today on the various modes to my dv10 rx. I found that there is barely no audio on Fm from the internal mic. Ssb seems ok. Also found when radio sat next to my Dv10 and sdr radio the 6100 gives of a carrier to my Sdr's and dv10 when not keying. Has anyone else had this ?

XIEGU X6100 No transmit power on FT8, both with WSJTX and JTDX

 XIEGU X6100 No transmit power on FT8, both with WSJTX and JTDX

I received my X6100 last week and was impressed with the build quality.

I successfully made contacts on SSB and CW. I configured JTDX and WSJTX and was able to recieve without issue with both but most of the time was not able to transmit, oddly enough sometime it worked, which made no sense. This setup was using my laptop with windows 11 and a USB-C to USB-C connection to the radio. Most of the time no matter what I did it would key to transmit but no output power. After watching quite a few youtube videos on how to configure it, nothing seemed to work. After many hours of troubleshooting, on a wilm, I used WSJTX in tune mode to key the radio which showed 0 power, then had windows sent a test pattern through the usb port instead of speaker and low and behold i got transmit power (on a dummy load of coarse).

To further the test, I configured my raspberry PI with WSJTX and connected using the same cabling to the radio and it works first time and every time since.

This leads me to believe that the WSJTX and JTDX software does not reliably send audio thru the windows USB-C audio port. My dell only has USB-C. I have tried both the windows standard drivers and the Xiegu cable driver from the radioddity.com site. Since windows sounds go through the port just fine, I am beginning to believe it is not a windows issue.

I have seen a few others on the group having the same transmit issue and am wondering if my test can be duplicated elsewhere.

X6100 filters in CW mode

X6100 filters in CW mode


Is there a way to widen filter #1 when in CW mode?

I find 500Hz way too narrow when generally tuning about in the CW end of a band: I would like to be able to set it anywhere from 2.4kHz down to, say, 1.2kHz. I would like to have filter #2 set to 500Hz and then if things got really bad have filter #3 set for 250Hz - or less.

You can tune about with the X6100 set to LSB to get a larger 'listening' bandwidth but if you then change the mode to CW you have to remember that the tuning will be out by whatever tone you've set the radio to.


X6100 screen glare during field operations

X6100 screen glare during field operations

Has anyone found a good anti-glare screen protector? Have you found that it helps with seeing the screen better in during field operations?